Local Reviews
for Pataskala, OH
Powered by Nearby NowGreat service
Rudra - Pataskala, OH
exceptional work
Ken - Pataskala, OH
Isaiah was very professional and informative. He explained everything he was going to do and answered all my questions. He gave me recommendations for the future care of my HVAC system. I will certainly call New Albany Heating and Cooling in the future. Great job Isaiah!
Excellent service!
Beth - Pataskala, OH
Bryan was pleasant and courteous while completing the most thorough inspection my system has ever had. He went above and beyond what was required, and I greatly appreciate it. I will request him for future service calls.
Very satisfied customer
Jeff - Pataskala, OH
If I ever need heating or cooling work done again, it will be through this company. The repairman came on time, fixed the problem, and even came back the same day to make sure it was fixed. The price was very reasonable.
Very Respectful
Rob - Pataskala, OH
They showed up exactly when they said they were going to be. Very respectful and courteous. Answered all my question and very knowledgeable about HVAC.
Furnace check
Chuck - Pataskala, OH
Great service. Informative and thorough.
Randal S.
I completed spring tune up on a Bryant heat pump. I visually inspected the furnace. I inspected the evaporator coil. I checked the temperature difference across the coil. Checked voltage and amps. Inspected heat pump. Checked refrigerant charge, voltages and amps. I rinsed the condenser coils with water. Cycled and monitored the system. Operating normally at this time.
Randal S.
I completed the scheduled maintenance agreement cooling tune up on a Goodman air conditioner. I visually inspected the unit. Checked voltages, amps and pressures. Completed combustion analysis. I inspected the evaporator coil. I checked the temperature difference across the coil. Checked voltage and amps. Inspected heat pump. Checked refrigerant charge, voltages and amps. I rinsed the condenser coils with water. Cycled and monitored systems. All operating normally at this time.
Pooya Y.
I completed a service call for a furnace kicking on and right back off. Furnace was not operational upon arrival. Fresh air intake was clogged. Cleared all debris from intake. System ran for 20 mins with no errors, operational upon departure.
Pooya Y.
I completed scheduled maintenance spring tune up on a Carrier Air Conditioner. I visually inspected the furnace, the evaporator coil. I checked the temperature difference across the coil. Checked voltage and amps. Inspected heat pump. Checked refrigerant charge. I rinsed the condenser coils with water. Operating normally at this time.
Randal S.
I completed a diagnostic on a Gas Furnace. I determined that the Ignitor was broken. I replaced the Ignitor, system was operational at time of departure
Randal S.
I completed a diagnostic on a 2020 Carrier Gas Furnace. Found that system was moving. Added rubber pads to keep it from moving and centered system. System operational at time of departure.
Randal S.
I arrived at customer's home and found that furnace unit was leaking at the bottom. I took boot out and put coupler in so it is a straight line of pvc with no boot to eliminate leaking issue. System operating as intended upon departure.
Randal S.
I completed a diagnostic on a Comfortmaker gas furnace. Determined that large spider nest was in gas oriffice and flame sensor needed cleaned. System was operational at time of departure.
Austin M.
I completed a duct cleaning before install of Carrier 80% 70,000 BTU Gas Furnace and Carrier 13 SEER 3 Ton Air Conditioner
Pooya Y.
Upon arrival for callback on 2020 Carrier furnace, furnace was operational after about 10 minutes it tripped on high limit showing led code 33. After further diagnosis, discovered that the merv13 air filter is pretty clogged up recommended to customer to go to a merv8 instead, also noticed 5 dampers on ductwork has been 3/4 way shut. Opened all dampers and removed filter. Checked board on wiring and noticed W2 was wired to stat which would cause t-stat to control staging vs the main circuit board, unhooked W2 so the furnace main circuit board would control staging not the stat. After high limit switch cooled off and remade furnace went through heat cycle and kicked on. System continued to operate as intended for about 25 minutes without showing any fault or errors. System operational at departure.
